: | Oct 22, 2004 |
Variant without oil cooler shown. |
DESCRIPTION | TYPE |
---|---|
Configuration | 60 degree V6 |
Maximum power | 156 kW at 4750 rpm |
Maximum torque | 346 Nm at 3000 rpm |
Displacement | 4009cc |
Stroke/bore | 84.4mm/100.4mm |
Compression ratio | 9.7:1 |
Firing order | 1 4 2 5 3 6 |
Oil capacity | 6.4 litres |
Variant with oil cooler shown. |
1 | - | Piston Rings |
2 | - | Piston |
3 | - | Piston pin |
4 | - | Connecting rod |
5 | - | Connecting rod bearing - upper |
6 | - | Connecting rod bearing - lower |
7 | - | Connecting rod cap |
8 | - | Oil filter |
9 | - | Oil cooler (if fitted) |
10 | - | Oil filter adapter mounting bolt |
11 | - | O ring |
12 | - | O ring |
13 | - | Oil filter adapter |
14 | - | O ring |
15 | - | Knock sensor |
16 | - | Cylinder block |
17 | - | Locating dowel |
18 | - | Knock sensor |
19 | - | Oil pressure switch |
20 | - | Starter motor |
21 | - | Gasket |
22 | - | Front cover |
23 | - | Seal |
24 | - | Gasket |
25 | - | Water pump |
26 | - | Crankshaft pulley |
27 | - | Jackshaft shaft chain |
28 | - | Jackshaft shaft sprocket |
29 | - | Chain tensioner |
30 | - | Jackshaft shaft |
31 | - | Jackshaft thrust plate |
32 | - | Chain guide |
33 | - | Chain guide |
34 | - | Oil gallery plug |
35 | - | Plug |
36 | - | Spacer |
37 | - | Oil gallery plug |
1 | - | Engine data |
2 | - | Engine data |
3 | - | Vehicle Identification Number (primary location) |
4 | - | Vehicle Identification Number(secondary location) |
1 | - | Piston ring, upper compression |
2 | - | Piston ring, lower compression |
3 | - | Piston rings, oil control |
4 | - | Piston |
5 | - | Piston pin |
6 | - | Connecting rod |
7 | - | Oil squirt hole |
8 | - | Connecting rod bearing, upper |
9 | - | Connecting rod bearing, lower |
10 | - | Connecting rod cap |
11 | - | Nut |
12 | - | Bolt |
1 | - | Jackshaft |
2 | - | Thrust plate |
1 | - | Water pump assembly |
2 | - | Engine front cover |
3 | - | Gasket |
Variant with oil cooler shown. |
1 | - | O ring |
2 | - | Adapter |
3 | - | O ring |
4 | - | O ring |
5 | - | Adapter mounting bolt |
6 | - | Cooler assembly (if fitted) |
7 | - | Oil filter |
1 | - | RH knock sensor |
2 | LH knock sensor |
1 | - | Oil Pressure Switch |
1 | - | Tensioner |
2 | - | Chain |
3 | - | Balance shaft assembly |
4 | - | Main bearing, upper |
5 | - | Main thrust bearing, upper |
6 | - | Crankshaft |
7 | - | Crankshaft oil seal, rear |
8 | - | Main thrust bearing, lower |
9 | - | Main bearing, lower |
10 | - | Main bearing cap, rear |
11 | - | Intermediate shaft |
12 | - | Oil pump |
13 | - | Pick-up pipe adapter |
14 | - | Ladder frame |
15 | - | Oil pick-up pipe |
16 | - | Sump |
17 | - | Crankshaft oil seal, front |
18 | - | Key |
1 | - | Main bearing cap |
2 | - | Main bearing, lower |
3 | - | Key |
4 | - | Crankshaft |
5 | - | Main bearing, upper |
6 | - | Main bearing, thrust |
1 | - | Drive chain |
2 | - | Tensioner assembly |
3 | - | Balance assembly |
4 | - | Chain guide |
A | - | Rear |
B | - | Front |
1 | - | Rear seal |
2 | - | Front cover |
3 | - | Front seal |
1 | - | Oil pump |
2 | - | Pick-up pipe adapter assembly |
3 | - | Intermediate shaft |
4 | - | Clamp |
5 | - | Drive assembly |
A | - | 69.8 mm minimum |
1 | - | Engine bulkhead housing |
2 | - | Crankshaft main bearing cap adjustment screw |
1 | - | Sump |
1 | - | Oil pick-up |
A | - | Front of engine |
1 | - | LH camshaft drive assembly |
2 | - | RH camshaft drive assembly |
3 | - | Spacer |
4 | - | Jackshaft sprocket |
5 | - | Chain guide |
6 | - | Jackshaft chain tensioner |
7 | - | Tensioner pin |
8 | - | Jackshaft chain |
1 | - | Hose, crankcase emissions, RH camshaft cover to intake manifold |
2 | - | Fuel injector pulse damper |
3 | - | RH Fuel rail |
4 | - | LH injectors (3 of) |
5 | - | Fuel supply line |
6 | - | Schrader valve |
7 | - | RH injectors (3 of) |
8 | - | Hose, crankcase emissions, LH camshaft cover to intake manifold |
9 | - | Electrically heated positive crankcase ventilation valve |
10 | - | Camshaft position (CMP) sensor |
11 | - | Oil filler cap |
12 | - | LH camshaft cover |
13 | - | LH valve rocker arm oil supply tube |
14 | - | LH camshaft bearing caps |
15 | - | LH camshaft |
16 | - | Valve rocker arm |
17 | - | Collet |
18 | - | Valve spring retainer seat |
19 | - | Hydraulic lash adjuster |
20 | - | Valve spring |
21 | - | Valve stem seal |
22 | - | LH cylinder head |
23 | - | LH exhaust manifold gasket |
24 | - | Valves |
25 | - | Cylinder head gasket |
26 | - | Volume reduction plug/valves |
27 | - | Timing chain tensioner |
28 | - | RH exhaust manifold gasket |
29 | - | Timing chain tensioner |
30 | - | RH cylinder head |
31 | - | RH camshaft |
32 | - | RH camshaft bearing caps |
33 | - | RH valve rocker arm oil supply tube |
34 | - | RH camshaft cover |
35 | - | Crankcase ventilation valve |
1 | - | RH cylinder head |
2 | - | LH cylinder head |
1 | - | Bearing cap |
2 | - | Camshaft |
1 | - | Valve stem seal |
2 | - | Valve spring |
3 | - | Valve spring retainer seat |
4 | - | Valve spring retainer key |
5 | - | Rocker arm |
6 | - | Hydraulic lash adjuster |
7 | - | Valve |
1 | - | Valve rocker arm oil supply tube |
1 | - | LH cylinder head gasket |
2 | - | RH cylinder head gasket |
1 | - | Fuel rail |
2 | - | Injector |
3 | - | Adapter |
1 | - | Crankcase ventilation valve |
2 | - | RH camshaft cover |
3 | - | LH camshaft cover |
4 | - | Oil filler cap and extension |
5 | - | Camshaft Position (CMP) sensor |
6 | - | Electrically heated positive crankcase ventilation valve |
1 | - | CMP sensor |
Variant with oil cooler shown. |
1 | - | Oil level gauge |
2 | - | Oil level gauge tube |