:	Jan 3, 2008

.

: Do not turn the ignition on when the parking brake has been set to the mounting position. Using the Land Rover approved diagnostic system, drive the parking brake to the mounting position.

.

Isolate the parking brake electrical circuit.   Remove fuse number 8 from the battery junction box (BJB).

.

: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.

.

Remove the evaporative emissions canister.

.

Remove the rear wheels and tires.

.

Release the parking brake shoe adjustment.   Loosen the screws.

.

: Do not allow the brake caliper to hang on the brake hose. :   LH is shown, RH is similar. Reposition the RH rear brake caliper.   Remove the 2 bolts.   Using a suitable tie strap, support the brake caliper.

.

Remove the RH rear brake disc.   Remove the screw.

.

: Do not allow the brake caliper to hang on the brake hose. Reposition the LH rear brake caliper.   Remove the 2 bolts.   Using a suitable tie strap, support the brake caliper.

.

Remove the LH rear brake disc.   Remove the screw.

.

:   RH is shown, LH is similar. Disconnect both parking brake cables from the wheel hubs.   Fully loosen the nut.   Release the parking brake cable from the lower arm.   Disconnect the inner parking brake cable from the brake shoe.

.

Release the LH parking brake cable.   Remove the 2 bolts.   Release the 3 wiring harness clips.   Release the cable from the clip on the chassis.

.

Release the LH parking brake cable.

.

: The fuel tank breather line bracket can be easily damaged when releasing it from the chassis. Release the fuel tank breather line bracket.   Remove the plastic insert.

.

Release the RH parking brake cable.   Remove the 2 bolts.   Release the parking brake cable from the 2 pipe clips.   Release the parking brake cable from the clip on the chassis.

.

Release the RH parking brake cable.

.

Remove the fuel tank heat shield.   Remove the 3 bolts and 2 nuts.

.

: Inspect the parking brake emergency release cable to body seal and replace if damaged. :   Note the fitted position of the parking brake emergency release cable to body seal. Release the parking brake emergency release cable.

.

Remove the parking brake actuator mounting bracket.   Release the air suspension pipe clips.   Remove the 2 nuts.   Remove the 5 bolts.   Release the 3 wiring harness clips.

.

:   Note the routing of the parking brake emergency release cable. :   Note the routing of the parking brake cables. Remove the parking brake actuator and cable assembly.   Disconnect the electrical connector.

.

:   Note the routing of the parking brake emergency release cable. :   Note the routing of the parking brake cables. Install the parking brake actuator and cable assembly.   Connect the electrical connector.

.

Install the parking brake actuator mounting bracket.   Tighten the bolts to 22 Nm (16 lb.ft).   Tighten the nuts to 10 Nm (7 lb.ft).   Secure the air suspension pipe.   Secure the wiring harness.

.

: Make sure the parking brake emergency release cable to body seal is installed correctly. Locate and secure the parking brake emergency release cable.

.

Install the fuel tank heat shield.   Tighten the bolts to 6 Nm (4 lb.ft).   Tighten the nuts to 3 Nm (2 lb.ft).

.

Locate and secure the RH parking brake cable.   Tighten the bolts to 22 Nm (16 lb.ft).   Secure the parking brake cable to the 2 pipe clips.   Secure the parking brake cable grommet to the integrated body frame bracket.

.

Secure the fuel tank breather line bracket.   Install the plastic insert.

.

Locate and secure the LH parking brake cable.   Tighten the bolts to 22 Nm (16 lb.ft).   Secure the wiring harness.   Secure the parking brake cable grommet to the integrated body frame bracket.

.

: Pull on the parking brake cable to make sure the inner parking brake cable is engaged in the parking brake shoe lever. :   Make sure that the brake cable circlip is positioned as shown. Connect the parking brake cables to the wheel hubs.   Connect the parking brake cable to the brake shoe lever.   Locate the parking brake cable to the backplate.   Tighten the nut to 8 Nm (6 lb.ft).

.

: Make sure that the component is clean, free of foreign material and lubricant. Install the LH rear brake disc.   Tighten the screw to 35 Nm (26 lb.ft).

.

Secure the LH rear brake caliper.   Remove and discard the tie strap.   Tighten the bolts to 115 Nm (85 lb.ft).

.

: Make sure that the component is clean, free of foreign material and lubricant. Install the RH rear brake disc.   Tighten the screw to 35 Nm (26 lb.ft).

.

Secure the RH rear brake caliper.   Remove and discard the tie strap.   Tighten the bolts to 115 Nm (85 lb.ft).

.

Adjust the parking brake shoes.

.

Install the evaporative emissions canister.

.

Install the wheels and tires.   Tighten the wheel nuts to 140 Nm (103 lb.ft).

.

Install fuse number 8 into the BJB.

.

Using the Land Rover approved diagnostic system, calibrate the parking brake actuator on an even surface.