: | Jun 18, 2007 |
. |
:
The frame wiring harness routing. |
. | Open the upper liftgate and lower tailgate. |
. | Remove the spare wheel and tire. |
. |
Raise and support the vehicle. |
. | Remove the wheels and tires. |
. | Disconnect the battery ground cable. |
. | Remove the LH front wheel arch liner. |
. | Remove the windshield washer reservoir filler
neck. |
. | LH side behind the front headlamp: Disconnect
the frame wiring harness electrical connector. |
. | LH side behind the front panel: Disconnect the 2 electrical connectors from the frame wiring harness. |
. | LH side behind headlamp: Release the 2 clips
from the inner fender. |
. | LH side behind headlamp: Reposition the frame wiring harness down to the inner fender. |
. | LH side front: Release the 2 windshield washer
jet hoses. |
. | Remove the frame wiring harness carrier.
|
. | LH side front: Disconnect the height sensor
electrical connector. |
. | Disconnect the ground cable from the wheel arch
earth stud.
|
. | LH front side: Release the frame wiring harness
from the frame.
|
. | Remove the air suspension reservoir. |
. | LH side: Release air suspension line from the
frame wiring harness.
|
. | LH side: Release the frame wiring harness from
the frame.
|
. | Remove the air suspension silencer. |
. | Remove the evaporative emission canister. |
. | Disconnect the 2 electrical connectors from the
air suspension solenoid. |
. | Release the air suspension compressor valve
block.
|
. | LH side: Release air suspension line from the
frame wiring harness. |
. |
Release both stabilizer bar links.
|
. | Release the stabilizer bar.
|
. | Release the frame wiring harness from the
parking brake cable. |
. | Vehicles with differential locking motor:
Disconnect the 2 electrical connectors.
|
. | Release the parking brake emergency release
cable.
|
. | LH side: Release the frame wiring harness.
|
. | Disconnect the electrical connector from the
rear LH height sensor.
|
. | LH side rear: Disconnect the air suspension rear
valve block electrical connector.
|
. | Release the valve block from its mounting
bracket.
|
. | Reposition the frame wiring harness to above the frame. |
. | LH side rear: Disconnect the 2 electrical
connectors from the frame wiring harness.
|
. | Disconnect the LH rear ABS sensor.
|
. | Release the parking brake actuator mount
bracket. |
. | Spare wheel aperture: Release the frame wiring
harness.
|
. | RH side rear: Disconnect the ABS sensor
electrical connector.
|
. | RH side rear: Disconnect the low brake pad
warning lamp electrical connector.
|
. | Disconnect the electronic parking brake actuator
electrical connector.
|
. | Release the RH parking brake cable.
|
. | Release the fuel line support bracket.
|
. | Release the frame wiring harness from the
parking brake cable. |
. | RH side: Release the frame wiring harness from the frame. |
. | Remove the transmission under shield.
|
. | Remove the fuel tank heat shield.
|
. | Release the parking brake emergency release
cable.
|
. |
Using a transmission jack, lower the fuel tank.
|
. | Disconnect the fuel pump module electrical
connector. |
. | Release the frame wiring harness from the fuel
tank. |
. | Rear of fuel tank: Release the frame wiring
harness from the top of the frame crossmember.
|
. | Secure the fuel tank. |
. | Release the exhaust heat shield for access.
|
. | Release the brake pipes. |
. | With assistance, remove the frame wiring
harness.
|
. | Check the old frame wiring harness against the new frame wiring harness to make sure that they are the same. |
. |
:
With assistance, install the frame wiring harness.
|
. | Secure the brake pipes. |
. | Secure the exhaust heat shield. |
. |
Using a transmission jack, lower the fuel tank.
|
. | Connect the fuel pump module electrical connector. |
. | RH side: Secure the frame wiring harness to the fuel tank. |
. | Rear of fuel tank: Secure the frame wiring harness to the top of the frame crossmember. |
. |
Install the fuel tank.
|
. | Secure the parking brake emergency release
cable.
|
. | Install the fuel tank heat shield.
|
. | Install the transmission under shield.
|
. | RH side: Secure the frame wiring harness to the frame. |
. | Secure the frame wiring harness to the RH parking brake cable. |
. | Secure the RH parking brake cable bracket.
|
. | Secure the RH parking brake cable.
|
. | Connect the electronic parking brake actuator
electrical connector.
|
. | RH side rear: Connect the low brake pad warning
lamp electrical connector.
|
. | RH side rear: Connect the ABS sensor electrical
connector.
|
. | Spare wheel aperture: Secure the frame wiring
harness.
|
. | Secure the parking brake actuator mount bracket.
|
. | Connect the LH rear ABS sensor.
|
. | LH side rear: Connect the 2 electrical
connectors to the frame wiring harness.
|
. | Reposition the rear valve block electrical connector. |
. | Reposition the RH side rear height sensor electrical connector. |
. | LH side rear: Connect the air suspension valve
block electrical connector.
|
. | Connect the electrical connector to the rear LH
height sensor.
|
. | Secure the valve block to its mounting. |
. | LH side: Secure the frame wiring harness.
|
. | Secure the parking brake emergency release
cable.
|
. | Secure the frame wiring harness to the LH parking brake cable. |
. | Attach both stabilizer bar links.
|
. | Secure the stabilizer bar.
|
. | Install the rear wheels and tires. |
. | Secure the air suspension compressor valve block. |
. | Connect the electrical connectors to the air suspension solenoid. |
. | Install the air suspension silencer. |
. | LH side: Secure the air suspension line to the frame wiring harness. |
. | LH side: Secure the frame wiring harness to the
frame.
|
. | Install the air suspension reservoir. |
. | Connect the ground cable to the wheel arch earth
stud.
|
. | LH side front: Connect the height sensor electrical connector. |
. | Install the frame wiring harness carrier.
|
. | LH side front: Secure the 2 windshield washer jet hoses. |
. | Reposition the frame wiring harness through the inner fender. |
. | LH side behind headlamp: Secure the 2 clips to the inner wing. |
. | LH side behind the front panel: Connect the 2 electrical connectors to the frame wiring harness. |
. | LH side behind the front headlamp: Connect the frame wiring harness electrical connector. |
. | Install the windshield washer reservoir filler neck. |
. | Install the LH front wheel arch liner. |
. | Connect the battery ground cable. |