This is a publication of Fluke Industrial B.V.,
		DIAGNOSTIC TOOLS DIVISION
		 Almelo, The Netherlands
	      © 1995,1997 Fluke Corporation


   Product      :  SW33W for Windows
                   FlukeView® CombiScope® Software

   Version      :  2.0 DEMO
   Date         :  November 19, 1997

   Contents:    1. Demo with limited functionality
                2. "Duplicate File Found" message during SETUP
                3. Known problems with FlukeView

   _____________________________________________________________

   1. DEMO WITH LIMITED FUNCTIONALITY

   This demo will give you an impression of the functionality
   of the FlukeView CombiScope software for Windows.

   All functionality is available, with the only exception that:

       - Saving to file
       - Copying to clipboard
       - Printing

   is either not possible or gives demo output.

   Note that when a file is saved with an existing filename,
   the program will delete the existing file and not save data
   to a new file.

   When no CombiScope is connected, the program will simulate
   data transfer with a CombiScope model PM3394A. In this case,
   the Connect button must be activated in the Instrument Connect
   dialog box that is displayed after starting the program.

   In combination with a Fluke CombiScope instrument, FlukeView
   is the ideal software package for documenting, archiving and
   analyzing your measurements.

   The following CombiScopes are supported:

      PM3394B   PM3394A   PM3394
                PM3392A   PM3392
      PM3390B   PM3390A
      PM3384B   PM3384A   PM3384 PM3384E
                PM3382A   PM3382
      PM3380B   PM3380A
      PM3370B   PM3370A
 
   connected to the PC via the PM8914 Serial Interface Cable. 


   Ordering information:

      SW33W/012:   FlukeView CombiScope for Windows

   For more information, call one of the following:

      In the U.S.A.:      (800) 443-5853  or fax (425) 356-5116
      In Europe:          (31-40) 2678200 or fax (31-40) 2678222
      In Canada:          (905) 890 7600  or fax (905) 890 6866
      In other countries: (1-425) 356-5500

   ______________________________________________________________

   2. "DUPLICATE FILE FOUND" MESSAGE DURING SETUP

   The setup program of FlukeView, copies the files PDQCOMM2.VBX,
   CMDIALOG.VBX, COMMDLG.DLL, THREED.VBX, VBCTL3D.VBX 
   and VBRUN300.DLL to the SYSTEM directory of WINDOWS.

   The following message will be given when one of these files 
   is originally present in the \WINDOWS\SYSTEM directory:

      "File <filename> is already present. If FlukeView cannot
       be started, remove the file <filename>"

   When this message is shown, FlukeView does not replace the
   original file in your WINDOWS\SYSTEM directory. If FlukeView
   cannot be started, the original file is not compatible with
   the <filename> version supplied with FlukeView.

   To start FlukeView, rename the file <filename> for backup
   reasons and run the FlukeView Setup program again.
 
   ______________________________________________________________

   3. KNOWN PROBLEMS WITH FLUKEVIEW

   Please note the following problems you may encounter when 
   using FlukeView for Windows:

   a. When a mouse is connected to a COM port with the same
      interrupt level as the COM port to which the CombiScope is
      connected, the connection to the CombiScope may fail.
      This can occur when COM1 and COM3 (or COM2 and COM4) are
      used, for example.
      To solve this problem, connect the mouse or the CombiScope
      to another COM port or change the interrupt level of a COM
      port (refer to the documentation of the PC or the serial
      interface card).

   b. During communication with the CombiScope, when you move the
      mouse over the border of a window or over the stop button,
      the following error may occur:

         "Communication error: Overrun error detected."

                                Tip

      Select the standard VGA display from the Windows Setup
      to overcome this problem.

   c. When the mouse is positioned above a button on the toolbar,
      the statusbar displays a text that describes the button. If
      the mouse is quickly moved away, the text may not disappear.

   d. When resizing a window results in large text characters, 
      disable the Windows setting "True Type Fonts Only".

      For Windows 3.1, start the Control Panel program and select
      Fonts, True Type... and disable "Show Only True Type Fonts 
      in Applications".

      For Windows 95, select My Computer, Control Panel, Fonts,
      View - Options, True Type, and disable "Show only True Type
      fonts in the programs on my computer".

      For Windows NT, select My Computer, Control Panel, Fonts,
      View - Options, True Type Fonts, and disable "Show only True
      Type fonts in the programs on my computer".

   e. When the CombiScope is in the Single Trigger mode and no
      waveform has been acquired yet, the error message "Timeout"
      is given. 

   ______________________________________________________________

   End of the README.TXT file.